our special tools
sensor drone
The MagArrow II is the second generation of our best-selling UAS-enabled magnetometer and it’s setting a new standard for UAS magnetic surveys. The MagArrow is engineered to simplify surveys that are difficult due to the various limitations of pilot-on-board surveys and ground surveys. The MagArrow is a robust yet flexible system that can adapt to changing field conditions and new user workflows.
The MagArrow consists of an aerodynamic, light-weight shell with internal electronics including the MFAM™ magnetic sensors, GPS, and IMU. The MFAM™, a two sensor module inside the MagArrow is our most groundbreaking magnetometer yet, capable of highly precise measurements in an extremely lightweight and tiny package.
scanning Cart
Experience a significant boost in efficiency with the latest generation of the worldwide tried and tested UPEX® 740 M large loop. This flexible detection system of 1-2 m2 facilitates speedy surface surveying with a high level of depth penetration. To adapt to the local searching conditions, this new device is equipped with 3 search sensitivity levels LOW / MEDIUM / HIGH. An MK 82 could be detected at level MEDIUM at a depth of approximately 3 m.
The large loop delivers a wide detection range for mediumsized and large metal objects and can block out interference caused by strands of wire, nails, and low-volume scrap metal. This reduces the need for unnecessary excavation and speeds up the progress of work.
The large loop delivers a wide detection range for mediumsized and large metal objects and can block out interference caused by strands of wire, nails, and low-volume scrap metal. This reduces the need for unnecessary excavation and speeds up the progress of work.
The MagArrow consists of an aerodynamic, light-weight shell with internal electronics including the MFAM™ magnetic sensors, GPS, and IMU. The MFAM™, a two sensor module inside the MagArrow is our most groundbreaking magnetometer yet, capable of highly precise measurements in an extremely lightweight and tiny package.
Armored excavator
The excavator, also known as a “Bagger”, is a piece of mechanical engineering equipment that consists of a long digging arm with a bucket (backhoe) mounted on a rotating platform (“pivot”) that moves on tracks. The excavator is a heavy and slow machine, but it has a variety of uses. By default, the digging arm is equipped with a bucket, but it can be replaced with a pneumatic hammer (“air hammer”) – which is mainly used for demolishing buildings – or a shearer (a device resembling large scissors), a grapple, and even a drill..
civil engeneering
4M Defence explosive engineers are an export in harnessing the mighty power of explosives for civil purposes in quarrying, tunneling and all other application uses we are here to by your partner in planning, design and carry out the work in a safe and controlled way your needs
Digger
4M Defense owns the DIGGER DTS D250, the “Swiss Army Knife” of mine clearance. The 250D is a remotely-operated tool designed for a wide range of tasks without the need for close human proximity. The 250D’s capabilities allow it to adapt to any terrain and operation type thanks to a variety of attachable tools, making it the most versatile tool in the industry
Digger scraper
Now you, too, can control your machines remotely Your machine operators are safe with SCRAPER Increased attention is being paid to the safety of construction machinery operators. It is not uncommon for excavators, bulldozers, loaders and dump trucks to be used in dangerous or challenging conditions: demolition work, where there is a risk of landslides, polluted areas, difficult topologies, noise, odours, etc. and to protect oneself from danger, what better way than to stay out of it. SCRAPER allows you to convert your existing machines or future acquisitions to permit remote control. But working with an excavator, for example, without being in the cab, can in some cases be almost impossible. Thus SCRAPER has been designed to put you virtually in the driving seat of your machine, as if you were there. Binocular vision, peripheral cameras, live streaming and controls effectively with no perceptible time lag, driving characteristics that closely mirror those of your machine, etc. Everything has been thought through and tested to ensure a working experience that is as close as possible to that pertaining in the cab. The icing on the cake is that your SCRAPER-equipped machine can still be used normally, so there’s no need for a dedicated remote-controlled machine park.
duppen
4M Defense has specially adapted screening and sifting buckets for mine and unexploded ordnance (UXO) clearance. The company stocks buckets in various sizes and for different needs. The buckets can be attached to the company’s blast-protected excavators as well as to non-protected excavators. The company has a stock of spare parts available to ensure continuous operation.
Extermination
The MagArrow II is the second generation of our best-selling UAS-enabled magnetometer and it’s setting a new standard for UAS magnetic surveys. The MagArrow is engineered to simplify surveys that are difficult due to the various limitations of pilot-on-board surveys and ground surveys. The MagArrow is a robust yet flexible system that can adapt to changing field conditions and new user workflows.
The MagArrow consists of an aerodynamic, light-weight shell with internal electronics including the MFAM™ magnetic sensors, GPS, and IMU. The MFAM™, a two sensor module inside the MagArrow is our most groundbreaking magnetometer yet, capable of highly precise measurements in an extremely lightweight and tiny package.
EN 
UKR 
HE